I have forgotten
my Password

Or login with:

  • Facebookhttp://facebook.com/
  • Googlehttps://www.google.com/accounts/o8/id
  • Yahoohttps://me.yahoo.com

Multiple Continuous Beams

The deflection of Continuous Beams with more than one span.
+ View other versions (4)

Continuous Beams

When a Beam is carried on three or more supports it is said to be Continuous. It is possible to use an extension of the Moment-Area method ( See "Bending of Beams Part 3") to obtain a relationship between the Bending Moments at three points (Usually Supports.)

A beam is a horizontal structural element that is capable of withstanding load primarily by resisting bending. The bending force induced into the material of the beam as a result of the external loads, own weight, span and external reactions to these loads is called a bending moment.

MISSING IMAGE!

23287/Multiple-Continous-Beams-108.png cannot be found in /users/23287/Multiple-Continous-Beams-108.png. Please contact the submission author.

On the drawing the areas \inline A_1 and \inline A_2 are the Free Bending Moment areas obtained by treating the Beam as over two separate spans \inline l_1 and \inline l_2 . If the actual Bending Moments at these points are \inline M_1, \inline M_2 and \inline M_3. Then a Fixing Moment diagram consisting of two trapezia can be introduced and the actual Bending Moment will be the Algebraic sum of the two diagrams.

In the lower figure the Elastic Line of the deflected Beam is shown.

The deflections \inline \delta _1 and \inline \delta _2 are measure relative to the left hand support and are positive upwards. \inline \displaystyle \theta is the slope of the beam over the central support and \inline Z_1 and \inline Z_2 are the intercepts for \inline l_1 and \inline l_2

\therefore\;\;\;\;\;\;\theta  = \frac{Z_1 + \delta _1}{l_1} = \frac{Z_2\;+\[\delta _2 - \delta _1]}{l_2}

Note. This assumes that the slopes everywhere are small.

\frac{A_1\bar{x}_1 - (\displaystyle\frac{M_1\;l_1}{2})(\displaystyle\frac{2\;l_1}{3}) - (\displaystyle\frac{M_2l_1}{2})(\displaystyle\frac{2\;l_1}{3})}{E\;I} + \frac{\delta _1}{l_1}

\;\;\;\;\;\;\;= - \frac{A_2\bar{x}_2 + (\displaystyle\frac{M_3 l_2}{2})(\displaystyle\frac{2\;l_2}{3}) + (\displaystyle\frac{M_2l_2}{2})(\displaystyle\frac{2\;l_2}{3})}{E\;I} + \frac{\delta _2 - \delta _1}{l_1}

Note that \inline \displaystyle Z_2 is a negative intercept.

The above equation can be written as:

If \inline \displaystyle I_1 = I_2

If the supports are at the same level:

If the Ends are Simply Supported then \inline \displaystyle M_1 = M_3 = 0

Clapeyron's Equation Or The Equation Of Three Moments

Span is the distance between two intermediate supports for a structure, e.g. a beam or a bridge.

Equation (2) is the most general form of The Equation of Three Moments. Equations (3) (4) and (5) are simplifications to meet particular needs. Of these Equation (4) is the form most frequently required.

Example:
[imperial]
Example - Example 1
Problem
A Beam Ad 60 ft. long rests on supports at , , and which are at the same level. and The loading is 1 ton/ft. throughout and in addition a concentrated load of 5 tons acts at the mid-point of and a load of 2 tons acts at

Draw the Shear Force and Bending Moment diagrams.
Workings

Applying Equation (3) to the span

The Bending Moment at mid-point of

The Bending Moment at the mid-point of

To find the reactions at the supports:

for

for

And

23287/Multiple-Continous-Beams-109.png
+

By difference,

From the Shear Force diagram it can be seen that the maximum Bending Moment occurs either at a distance of 13.5 ft. from where:

Or at a distance of 10.5 ft. from where:

The combined Bending Moment diagram is shown at the bottom of the sketch.

Beams With More Than Two Spans.

Where a Beam extends over more than three Supports the Equation of Three Moments is applied to each group of three in turns. In general if there are \inline n Supports there will be \inline n - 2 unknown Bending Moments ( excluding the Ends) and \inline n - 2 equations to solve simultaneously.